铸钢螺旋闸门,不锈钢螺旋闸门

LMD铸钢螺旋闸门,不锈钢螺旋闸门

参考价: 面议

具体成交价以合同协议为准
2022-03-01 18:40:01
37
产品属性
关闭
浙江三精阀门有限公司

浙江三精阀门有限公司

初级会员1
收藏

组合推荐相似产品

产品简介

LMD铸钢螺旋闸门,不锈钢螺旋闸门,三精螺旋闸门 1、设计制造按GB12235-59 2、结构长度按GB12221-89 3、法兰尺寸按JB/T79-94 4、阀门检查和试验按GB13927

详细介绍

螺旋闸门SCREW GATE VALVE

       螺旋闸门用于建材、冶金、矿山、电力、化工、玻璃、轻工、粮食等行业的库顶、库底及进出口等。是控制流量变化较大,启动频繁,切断迅速的理想设备。

This valve is widely used at the   top and bottom of store house and carry port in metallurgical, mining, building material, food, chemical industries etc. It is the ideal equipment to control a great changing flow, to open and close frequently and to stop quickly. 

螺旋闸门结构特点Structure characteristic:

       结构简单、操作灵活、重量轻、无卡阻、切断快,特别适用于各类无粘度的固体、粉料及小于 Φ 10mm 的颗粒料,晶粒料的输送及流量调节,安装不受角度限制, 操作方便, 能随时调节开度。该阀门有手轮和链轮操纵两种操作形式, I 型为手轮, II 为链轮。单向和双向两种结构形式, LZD 为单向、 LZS 为双向。

This valve is simple in structure, handy to operate, light in weight, non-obstructive and quick to stop. It is suitable to be used to carry all kinds of solid material, particle and crystal particle whose diameter is below 10mm and to adjust the flow. It can be installed at any angle and operated handily. The size of its gate can be regulated at any time. This valve has two type of operation. One is manual wheel operation; the other is chain wheel operation. Ⅰ means manual wheel. Ⅱ means chain wheel. The valve has two type of construction LZD is signal direction and LZS is double direction. 

LMD铸钢螺旋闸门,不锈钢螺旋闸门,三精螺旋闸门工作原理Working principle

       主要由框架、闸板、丝杆、螺母等零件构成,用手转动手轮使丝杆带着丝杆螺母和闸板沿水平方向往复运动,达到闸门的启闭目的。

It is mainly made up of frame, gate board, screw pole, nut etc. Rotate the handwheel by hand, then the screw pole drives the nut and gate board move in horizontal to and fro to open or close the valve.

LMD铸钢螺旋闸门,不锈钢螺旋闸门,三精螺旋闸门主要零件材料及连接尺寸

类别

A×A

B×B

C×C

H

L

n-d

重量

单向

200×200

256×256

296×296

820

100

8-Φ12

62

250×250

306×306

346×346

930

100

8-Φ14

70.5

300×300

356×356

396×396

1050

100

8-Φ14

81

400×400

456×456

496×496

140

100

12-Φ14

114

450×450

510×510

556×556

1450

120

12-Φ18

130

500×500

560×560

606×606

1610

120

16-Φ18

147

双向

600×600

660×660

706×706

1830

120

16-Φ18

169

700×700

770×770

820×820

2130

140

20-Φ18

236

800×800

870×870

920×920

2440

140

20-Φ18

303

900×900

974×974

1030×1030

2660

160

27-Φ23

424

1000×1000

10741074

1130×1130

2870

160

24-Φ23

636

说明

LMD-单向

I-手轮

距地面小于1.7米用手轮,大于1.7米用链轮
链条节数M=0.105X-113(X是丝杆中心离地面度度)

LMD,三精螺旋闸门使用说明sage explanation:

本阀可水平安装或垂直安装 , 安装时两法兰连接中间必须加密封垫片 , 然后锁紧螺栓。操作时手轮顺时针旋转为阀关,反之为开,不得在手轮上再增加辅助杠杆。若*存放应使设备处于关闭状态,各传动部位应加润滑油,不允许露天存放或堆置。

It can be installed in horizontal or vertical. Sealing gasket must be put on the connected, then equably tight the bolt.

 You can not add assistant lever to the hand wheel. Clockwise turn of hand wheel means the closing of valve, otherwise it means opening.

The device should be in the shut-down if the valve-board is placed longer. Driving parts should add lubricated oil. Placing in the open air and piling up is not permitted.

三精阀门公司订货须知:

一、①螺旋闸门产品名称与型号②螺旋闸门口径③螺旋闸门是否带附件以便我们的为您正确选型④螺旋闸门的使用压力⑤螺旋闸门的使用介质的温度。二、若已经由设计单位选定三精公司的螺旋闸门型号,请按螺旋闸门型号直接向我司销售部订购。当使用的场合非常重要或环境比较复杂时,请您尽量提供设计图纸和详细参数,由我们的三精阀门公司专家为您审核把关。
感谢您访问我们的【
www。。cnsjfm。。cn三精公司】如有任何疑问.您可以致电给我们,我们一定会尽心尽力为您提供优质的服务。

上一篇:穿透式刀型闸阀产品特性及产品优点 下一篇:美国进口不锈钢闸阀(美国LEO力沃品牌):
提示

请选择您要拨打的电话:

7332 [{"ID":"755655","CompanyID":"52803","Title":"穿透式刀型闸阀产品特性及产品优点","Picture":"mt0002/3/20201217/637438126607079037770.jpg","PictureDomain":"img77","UpdateTime":"2024/11/18 7:45:08","CreateTime":"2024/11/18 7:45:08","ClassName":"技术交流","rn":"3"},{"ID":"755553","CompanyID":"52371","Title":"美国进口不锈钢闸阀(美国LEO力沃品牌):","Picture":"mt0002/3/20100715/634148310748281250.jpg","PictureDomain":"img43","UpdateTime":"2024/11/17 7:30:25","CreateTime":"2024/11/17 7:30:25","ClassName":"技术交流","rn":"4"}]