CN8201-R1-LV控制器 美国omega

1/16 Din通用温度和过程控制器，带8段斜坡/恒值功能
CN8201 Series
2年保修 新产品! CE OmegaCare
1/16 Din通用温度和过程控制器，带8段斜坡/恒值功能
CN8201 Series:1/16 Din通用温度和过程控制器，带8段斜坡/恒值功能
可配置的通用输入场
自动调谐，直接或反向作用是输出。
用户可选择的设定值的斜坡。
8、8个匝道浸泡
测量温度是在0.1°十进制显示或根据1000°f°
NEMA 4X面板
温度控制器的cn8200 /流程是非常通用的和用户友好的。酒店操作员需要审查这些参数只有在设置相关的特定的应用。双数字显示*的信息和流程的一瞥。个人识别的状态的LED的输出，报警，数字通信，和特殊的选项。cn8200 NEMA 4X的特点A的前面板和一个通用电源供应100和250 VAC接受120到250伏。A 24伏或24伏的电源选项是可用的。控制算法是可用的P，PI，PD，PID，或开/关。自动调谐的特征集的自动比例带，积分和导数，在setpoint过程提供。本文提供了稳定和快速的过程参数
八级斜坡/浸控制门8和8个标准ramps soaks和十进制显示，包括一对热电偶的等级，数字显示和信号过滤，比例极限和功率设置。双控制的输出可以配置为应用程序的各种控制和报警，报警输出和两个支持是可用的。在cn8200提供范围广泛的选项，包括RS-232和RS-485的远程数字通信、模拟setpoint五场，三维接触/数字输入模式，四探头磁辅助输出电压，和四阶。

规格
Performance
Accuracy: ±0.2% of full scale, ±1 digit
Setpoint Resolution: 1 count/0.1 count
Repeatability: ±1 count
Temperature Stability: 5 μV/°C (maximum)
TC Cold-Junction Tracking: 0.05°C/°C ambient
Common Mode Rejection: 100 dB
Series Mode Rejection: >70 dB
Process Sampling: 10 Hz (100 ms)
Inputs
Input Type: See Input Table
Digital Input: For remote setpoint, remote standby or ramp/soak run and hold
Thermocouple Lead Resistance: 100 ohms max for rated accuracy
Decimal Position: Selectable
Outputs
Output #1: Reverse or directacting, configured from menu
Output #2: Reverse or directacting, configured from menu
Mechanical Relay: Rated 5 A @120 Vac, 3 A @ 240 Vac, normally open (N.O.), normally closed (N.C.), (output 1); Rated 5 A @120 Vac, 3 A @ 240 Vac, N.O. (output 2)
Current: 4 to 20 mA, 500 ohm max (suffix F1, F2); 4 to 20 mA, 1000 ohm max (suffix FH1, FH2)
Voltage: 20 Vdc pulse
Solid State Relay: SSR, 120/240 Vac, zero voltage switched, rated 1 A continuous, 10 A surge @ 25°C
Alarms: Mechanical relay rated 5 A @ 120 Vac, 3 A @ 240 Vac, N.O.; Optically isolated SSR rated 1 A, 120/240 Vac @ 25°C; dc alarms, 24 Vdc
Transducer Power Supply: 5, 10, 12, 15 Vdc ±10%
Control Characteristics
Setpoint Limits: Limited to configured range for thermocouple and RTD; limited to scaled range
Alarms: Adjustable for high/low; selectable process or deviation
Rate (Derivative): 0 to 2400 seconds
Reset (Integral): 0 to 9600 seconds
Cycle Time: 0.2 to 120 seconds
Proportional Band: 1 to span of sensor
Deadband: negative span to positive span of sensor
Hysteresis: 1 to span of sensor Autotune Damping: Adjustable (low, normal, or high)
Ramp to Setpoint: 1 to 9999 minutes
Autotune: Operator-initiated from front panel
Manual Control: Operator-initiated from front panel General
Power: 100 to 250 V, 50/60 Hz (single-phase), 120 to 250 Vdc, 24 Vac/24 Vdc optional
Display: Dual LED, 4-digit, orange: process display, green: menu/ parameter display; 9.2 mm (0.36")
Power Consumption: Less than 6 VA (instrument) @ 120 Vac
Weight: 226 g (8 oz)
Panel Cutout: 45 mm (1.771") square
Dimensions: 53.3 H x 53.3 W x 8.21 mm D (2.1 x 2.1 x 0.72") bezel
Depth Behind Panel: 100 mm (3.937")
Front Panel Rating: NEMA-4X
Operating Ambient Range: 0 to 55°C (32 to 131°F)
Humidity: 90% RH max, non-condensing
Memory Protection: Solid-state non-volatile memory
Connections: Screw terminals
Contacts: Twin bifurcated
Ramp/Soak Programming
Intervals: 8
Loops: 0 to 99
Ramp Time: 0 to 9999 minutes
Soak Time: 0 to 9999 minutes
Events/Alarms: 1 to 8
Ramp Setpoint: 1 to 9999 minutes
CN8-SW (Optional Software)
Minimum Hardware and Software Requirements: IBM PC or 100% compatible, Windows 95/98/NT; RS-485 interface or RS-232 to RS-485 converter
Software Compatibility: CN8200 Series controllers
Software Capability: Supports up to 254 CN8200 Series controllers.
Input and Range Table for Universal Input Controller
Input Type Range
J Iron Constantan -200 to 760°C (-328 to 1400°F)
K CHROMEGA?-ALOMEGA? -270 to 1354°C (-454 to 2469°F)
T Copper-Constantan -270 to 400°C (-454 to 752°F)
N OMEGALLOY? -268 to 1300°C (-450 to 2372°F)
R Pt/13%Rh - Pt -50 to 1768°C (-58 to 3214°F)
S Pt/10%Rh - Pt -50 to 1768°C (-58 to 3214°F)
B Pt/30%Rh - Pt/6%Rh 0 to 1820°C (32 to 3308°F)
C W/5%Re - W/26%Re 0 to 2315°C (32 to 4199°F)
E CHROMEGA?-Constantan -150 to 1000°C (-238 to 1832°F)
NNM 18% Molybdenem vs Nickel -06% Cobalt 0 to 1410°C (32 to 2570°F)
Platinel II -100 to 1232°C (-148 to 2250°F)
RTD (3-wire) 100 ohm PT -200 to 850°C (-328 to 1562°F)
RTD (3-wire) 100 ohm PT -199.9 to 375.0°C (-199.9 to 707.0°F)
0 to 1 V Scalable (-1999 to 9999) Selectable
1 to 5 V Scalable (-1999 to 9999) Selectable
0 to 5 V Scalable (-1999 to 9999) Selectable
0 to 10 V Scalable (-1999 to 9999) Selectable
10 to 50 mV Scalable (-1999 to 9999) Selectable
0 to 50 mV Scalable (-1999 to 9999) Selectable
0 to 10 mV Scalable (-1999 to 9999) Selectable
0 to 100 mV Scalable (-1999 to 9999) Selectable
4 to 20 mA Scalable (-1999 to 9999) Selectable
0 to 20 mA Scalable (-1999 to 9999) Selectable
Output Options–No Additional Cost
Option Type First Output-Heat or Cool
(Reverse or Direct) Order Suffix Second Output- Heat or Cool
(Reverse or Direct) Order Suffix
Relay -R1 -R2
dc Pulse -DC1 -DC2
1A SSR -T1 -T2
4 to 20 mA (500 ohm max) -F1 -F2
4 to 20 mA (800 ohm max) -FH1 -FH2
产品型号   产品描述
CN8201-R1-C4-DIC  Single Mechanical Relay output ramp/soak controller, RS485 with digital input, switch closed
CN8201-R1-C4-DIV  Single Mechanical Relay output ramp/soak controller, RS485 with digital input, 0 or 5 V
CN8201-R1-C4-MOD  Single Mechanical Relay output ramp/soak controller, RS485, Modbus
CN8201-R1-C4  Single Mechanical Relay output ramp/soak controller, RS485
CN8201-R1-C2  Single Mechanical Relay output ramp/soak controller, RS232
CN8201-R1-LV-AL1  Single Mechanical Relay output ramp/soak controller, low voltage, single alarm
CN8201-R1-LV  Single Mechanical Relay output ramp/soak controller, low voltage
CN8201-R1-PVSV2  Single Mechanical Relay output ramp/soak controller, Process output, PV or SV, 0 to 5 Vdc
CN8201-R1  Single Mechanical Relay output ramp/soak controller,0 or 5 Vdc remote setpoint with 1 alarm
CN8201-R1  Single Mechanical Relay output ramp/soak controller
CN8201-DC1-AL1  Single output ramp/soak controller with Single DC pulse, single alarm
CN8201-T1-AL1  Single output ramp/soak controller with Single 1A SSR, single alarm
CN8201-R1-AL1  Single output ramp/soak controller with Single alarm mechanical relay
CN8201-R1-AL2  Single output ramp/soak controller with Dual alarms, ac SSR
CN8201-DC1-C4  Single dc Pulse output ramp/soak controller, RS485
CN8201-DC1-LV  Single dc Pulse output ramp/soak controller, low voltage
CN8201-DC1  Single dc Pulse output ramp/soak controller
CN8201-F1-C4-MOD  Single output ramp/soak controller with 4-20 mA (500 ohm max.), RS485, MODBUS
CN8201-F1-C4  Single output ramp/soak controller with 4-20 mA (500 ohm max.), RS485
CN8201-F1-C2  Single output ramp/soak controller with 4-20 mA (500 ohm max.), RS232
CN8201-F1-LV  Single output ramp/soak controller with 4-20 mA (500 ohm max.), low voltage
CN8201-F1-PVSV2  Single output ramp/soak controller with 4-20 mA (500 ohm max.), Process output, 0 to 5 Vdc
CN8201-F1-PVSV1  Single output ramp/soak controller with 4-20 mA (500 ohm max.), Process output, 4 to 20 mA
CN8201-F1  Single output ramp/soak controller with 4-20 mA (500 ohm max.)
CN8201-FH1-AL1  Single output ramp/soak controller with 4-20 mA (1000 ohm max.), single alarm
CN8201-FH1-C2  Single output ramp/soak controller with 4-20 mA (1000 ohm max.), RS232
CN8201-FH1  Single output ramp/soak controller with 4-20 mA (1000 ohm max.)
CN8202-F1-F2-AL1  Dual output ramp/soak controller, dual 4 to 20 mA (500 ohm max), single alarm
CN8202-F1-F2-C2  Dual output ramp/soak controller, dual 4 to 20 mA (500 ohm max), RS232
CN8202-F1-F2-XP1  Dual output ramp/soak controller, dual 4 to 20 mA (500 ohm max), Transducer power supply, 15 Vdc
CN8202-R1-R2-C4  Dual output ramp/soak controller, relay, relay, RS485
CN8202-R1-R2-C2  Dual output ramp/soak controller, relay, relay, RS232
CN8202-R1-R2-AL2  Dual output ramp/soak controller, relay, relay, dual alarms
CN8202-R1-R2-AL1  Dual output ramp/soak controller, relay, relay, single alarm
CN8202-R1-R2-XP3  Dual output ramp/soak controller, relay, relay,Transducer power supply, 10 Vdc
CN8202-T1-T2-C2  Dual output ramp/soak controller, dual SSR outputs, RS232
CN8202-T1-T2  Dual output ramp/soak controller, dual SSR outputs
CN8202-R1-R2  Dual output ramp/soak controller, relay, relay
CN8202-R1-F2  Dual output ramp/soak controller, relay, 4 to 20 mA (500 ohm max)
CN8202-F1-F2  Dual output ramp/soak controller, dual 4 to 20 mA (500 ohm max)
CN8202-DC1-FH2  Dual output ramp/soak controller, dc pulse, 4 to 20 mA (800 . max)
CN8202-DC1-DC2  Dual output ramp/soak controller, dc pulse, dc pulse
CN8202-DC1-R2-C2  Dual output ramp/soak controller/RS-232 communications
CN8202-DC1-DC2-C4  Dual output ramp/soak controller/RS-485communications
CN8202-DC1-DC2-C2  Dual output ramp/soak controller/RS-232 communications
订购示例:(1)CN8202-R1-R2-LV-AL31/16 DIN dual mechanical relay outputs, ramp/soak process controller, low voltage power, with DC pulse alarms,
产品型号说明
(1)
(2)
(3)
(4)
(5)
CN820-
选项描述
(1)
Number of Outputs
选择
1代表Single Output
2代表Dual Output
(2)
First Output
选择
R1代表Relay
DC1代表dc Pulse
T1代表1A SSR
F1代表4-20 mA (500 ohm max.)
FH1代表4-20 mA (1000 ohm max.)
(3)
Second Output
选择
Nothing(leave field blank)代表No second output
-R2代表Relay
-DC2代表dc Pulse
-T2代表1A SSR
-F2代表4-20 mA (500 ohm max.)
-FH2代表4-20 mA (1000 ohm max.)
(4)
Low Voltage Power Input Option to operate unit
选择
Nothing(leave field blank)代表standard 100 to 250 Vac input power
-LV代表24 Vac/dc input power option
(5)
Additional Options
选择
Nothing(leave field blank)代表No additional options
-AL1代表Single alarm mechanical relay
-AL2代表Dual alarms ac SSR
-AL3代表Dual alarms dc level (24 Vdc)
-C2代表RS-232 communications
-C4代表RS-485 communications
-C4-DIC代表RS-485 with digital input- switch closed
-C4-DIO代表RS-485 with digital input- switch open
-C4-DIV代表RS-485 with digital input 0 or 5V
-C4-MOD代表RS-485 with modbus protocol
-C4-MOD-DIC代表RS-485 with modbus protocol with digital input switch closed
-C4-MOD-DIO代表RS-485 with modbus protocol with digital input switch open
-C4-MOD-DIV代表RS-485 with modbus protocol with digital input 0 or 5V
-PVSV2代表Process output PV or SV 0 to 5 Vdc
-RSP1代表Remote setpoint switch closed with 1 alarm
-RSP2代表Remote setpoint switch open with 1 alarm
-RSP3代表0 or 5 Vdc remote setpoint with 1 alarm
-XP1代表Transducer power supply 15 Vdc
-XP2代表Transducer power supply 12 Vdc
-XP3代表Transducer power supply 10 Vdc
-XP4代表Transducer power supply 5 Vdc
 

CN8201-R1-LV控制器 美国omega

相关产品：

CNi3224-C24控制器 美国omega温控